Un porte-à-faux de section rectangulaire repose sur une fondation élastique Winkler et chargé par une charge répartie. The image shows the calculation of the maximum deflection and maximum bending moment.
Une poutre en acier de section carrée est chargée avec un effort normal et une charge répartie. The image shows the calculation of the maximum bending deflection and critical load factor according to the second-order analysis.
Une poutre en acier chargée axialement avec une section carrée est fixée à une extrémité et supportée par un ressort à l'autre. Two cases with different spring stiffnesses are considered. The verification example solves the calculation of the load factors of the beam in the image using the linear stability analysis.
Un porte-à-faux avec des fibres qui ne s'étendent pas dans la direction de l'axe de la poutre à partir d'une section carrée soumise à une pression de traction. Calculate the maximum deflection.
Quatre poteaux sont encastrés en bas et reliés par un bloc rigide en haut. The block is loaded by pressure and modeled by an elastic material with a high modulus of elasticity. The outer columns are modeled by linear elastic material and the inner columns by a stress-strain diagram with decaying dependence. Assuming only the small deformation theory and neglecting the structure's self-weight, determine its maximum deflection.
Un porte-à-faux à inertie variable est entièrement fixé à l'extrémité gauche et chargé par une charge continue. Plastic material is considered for the calculation.
Un câble en acier ou une membrane avec des axes aux deux extrémités est chargé par une charge distribuée. Neglecting its self-weight, determine the maximum deflection of the structure using the large deformation analysis.
A vertical cantilever with a square cross-section is loaded at the top by tensile pressure. Le porte-à-faux est en matériau isotrope. Calculate the deflection.
A structure is made of two trusses, which are embedded into the hinge supports. The structure is loaded by concentrated force. le poids propre est négligé. Determine the relationship between the loading force and the deflection, considering large deformations.
A structure made of I-profile trusses is supported on both ends by spring sliding supports and loaded by transversal forces. Le poids propre est négligé dans cet exemple. Determine the deflection of the structure, the bending moment, the normal force in the given test points, and the horizontal deflection of the spring supports.
Considérez un tube d'échafaudage rigide, fixé en bas à l'aide de l'appui nodal d'échafaudage et chargé à la fois par un moment et une force. Self-weight is not considered. Considering an infinitely rigid beam, determine the maximum radial deflection.
Considérez un assemblage tubulaire d'un échafaudage soumis à un effort normal et un moment. Self-weight is not considered. The material of the tube is idealized as perfectly rigid. All geometrical non-linearities are ignored. Determine the angle of deflection.
Un porte-à-faux en acier de section rectangulaire est encastré d'un côté et libre de l'autre. The aim of this verification example is to determine the natural frequencies of the structure.
A cantilever beam with an I-beam cross-section of length L is defined. The beam has five mass points with masses m acting in the X-direction. le poids propre est négligé. The frequencies, mode shapes, and equivalent loads of this 5-DOF system are analytically calculated and compared with the results from RSTAB and RFEM.
Un porte-à-faux de section rectangulaire repose sur une fondation élastique de Pasternak et chargé par une charge répartie. The image shows the calculation of the maximum deflection and maximum bending moment.
Un mur en maçonnerie est exposé à une charge répartie au centre de sa partie supérieure. The Isotropic Masonry 2D material model is compared with the Isotropic Linear Elastic model, with surface stiffness property Without Tension in the nonlinear calculation.
A structure is made of two trusses of unequal length, which are embedded into the hinge supports. The structure is loaded by concentrated force. le poids propre est négligé. Determine the relationship between the loading force and the deflection, considering large deformations.
A structure made of an I-profile is fully fixed on the left end and embedded into the sliding support on the right end. The structure consists of two segments. Le poids propre est négligé dans cet exemple. Determine the maximum deflection of the structure, the bending moment on the fixed end, the rotation of segment 2, and the reaction force at point B by means of the geometrically linear analysis and the second-order analysis. The verification example is based on the example introduced by Gensichen and Lumpe.
Considérez un tube d'échafaudage rigide, fixé en bas à l'aide de l'appui nodal d'échafaudage et chargé à la fois par un moment et une force. Calculate the maximum deflection with consideration of initial slippage.